Tech Support

3000 PC Series Support   This page supports these models: 3014, 3024, 3210 These printers support the following emulations: - IBM-GP (3014-II, 3210) - Epson MX-80 (3014-I, 3024) - Okidata 84/2 ·Legacy· Technical support has been discontinued for all listed models. Introduced: Nov 85 End of Life: Sep 92 Replace by: 3460, 3480 What are PDF files, and why can't I read them? What does $ mean? Windows Windows Printing TechNotes Drivers Refer to TechNote 3000PC-DIP for support under Windows or other operating systems. Documentation ds3014 3014 Data Sheet ds3024 3024 Data Sheet ds3210 3210 Data Sheet $GEK-88499 3210 User's Manual $GEK-88430A 3014-I and 3024-I User's Manual (Epson MX+ and Okidata 84/2) $GEK-88442A 3014-II and 3024-II User's Manual (IBM Graphics and Okidata 84/2) $GEK-88429A 3014, 3024 and 3210 Service Manual TechNote 3000PC-DIP 3000 PC Series DIP Switch Settings 3014-I, 3014-II, 3024, 3210 To print the status, take the printer off-line, press and hold the LINE FEED key, then press the FORM FEED key. The DIP switch settings will print out. Please note that the switches are numbered from right to left, in the same physical order as the switch packs. The DIP switches are located inside the printer behind the front panel. The off position of the switch is towards the top of the printer. DIP switch changes do not take effect until the printer power is turned off and on. DIP Switches: Data bits 1-1   0 * eight (no parity) 1 seven Parity 1-2 1-3   0 * 0 even 0 1 odd 1 0 mark 1 1 space Interface Type and Baud Rate 1-4 1-5 1-6   0 0 0 serial - 9600 0 0 1 serial - 4800 0 1 0 serial - 2400 0 1 1 serial - 1200 1 0 0 serial - 600 1 0 1 serial - 300 1 1 0 serial - 110 two stop bits 1 1 1 * parallel Remote Select-Deselect / DTR Lead 1-7 Parallel Remote Select Deselect Serial DTR Lead Function 0 * disabled DTR reflects handshake 1 enabled DTR reflects power on only Strobe Polarity - Parallel 1-8   0 * Negative 1 Positive Emulation 2-1 2-2   0 0 * IBM-GP (3014-II, 3210) Epson MX-80 (3014-I, 3024) 0 1 Okidata 84/2 1 0 hex dump 1 1 factory test Slash zero character 2-3   0 * 3 1 Enabled Line Feed, Form Feed keys 2-4   0 * disabled when on line 1 enabled when on line Paper out sensor 2-5   0 disabled 1 enabled Paper Feeding Options 2-6 2-7   0 0 * continuous pin fed 0 1 Single Document Inserter 1 0 Automatic Sheet Feeder 1 1 reserved Busy Polarity - Parallel 2-8   0 * high is busy 1 low is busy Print Compression at Power Up 3-1   0 * 10 CPI 1 16.5 CPI (IBM-GP), 17 CPI (84/2) Skip Over Perf 3-2   0 * none 1 1 inch Line Spacing at Power Up 3-3   0 * 6 LPI 1 8 LPI Acknowledge Polarity - Parallel 3-8   0 * negative pulse 1 positive pulse Flight Time Compensation 4-1 4-2   0 0 * none 1 0 +0.4 ms 0 1 +0.8 ms 1 1 -0.8 ms National Character Set at Power Up 3-4 3-5 3-6 3-7   0 0 0 0 * US ASCII (84/2) Character Set 1 (IBM-GP) 1 0 0 0 British 0 1 0 0 German 1 1 0 0 French 0 0 1 0 Swedish 1 0 1 0 Danish 0 1 1 0 Norwegian 1 1 1 0 Dutch 0 0 0 1 Italian 1 0 0 1 Spanish 0 1 0 1 French B 1 1 0 1 French Canadian 0 0 1 1 Danish / Norwegian B 1 0 1 1 Danish / Norwegian C 0 1 1 1 Swedish / Finnish 1 1 1 1 TRS-80 (84/2) Character Set 2 (IBM-GP) Print Line Width 4-3   0 * 13.2 inches 1 8 inches Auto Wraparound at Right Margin 4-4   0 disabled 1 * enabled Auto LF on CR 4-5   0 * disabled 1 enabled Received <DEL> Code Action (84/2) 4-6   0 disabled 1 * enabled Forms Length at Power Up 4-7   0 11 inches 1 determined by position of front panel switch Select In Signal - Parallel 4-8   0 controlled by data source 1 * forced to zero volts

Specifications subject to change without notice. ® All trademarks are property of their respective holders at the time of this publication. If you have any questions or comments regarding this document, please contact TallyGenicom Technical Support. Copyright © 2000 — GENICOM,