| |
|
7600 Series TechNotes
|
|
7610
Introduced: Oct 93
End of Life: Jan 95
Replaced by: microLaser 210
|
This page supports these models: 7610, 7612,
7612i, 7612+, 7617, microLaser 17, microLaser 17e |
7612, 7612i, 7612+
Introduced: Nov 94
End of Life: Dec 96
Replaced by: microLaser 210
7617, microLaser 17, microLaser 17e
Introduced: Apr 97
Discontinued: Nov 99
Replaced by: microLaser 210 |
| 7610 |
7600-01
3 Aug 1995 |
Cover Will Not Close |
| The cover will not close when a print cartridge is installed. This usually occurs after
the printer has been shipped. |
7600-02
17 Feb 1997 |
71 Ozone Filter / 72
Change Filter |
| The display shows 71 OZONE FILTER or 72 CHANGE FILTER. |
7600-03
20 Aug 1997 |
Memory Upgrades |
| The 7160 uses standard 72 pin memory SIMM's, but not all memory may be compatible.
After installing memory, test it with the printer's built in memory check. |
7600-04
20 Aug 1997 |
Bar Code Left Offset |
| Barcodes using the printer resident barcode fonts cannot be printed less than 1.2 inches
from the left edge of the paper. |
7600-07
28 May 1996 |
Security Lock Override |
| The 7600 series have a Lock feature to provide security against inadvertent change
to the printer setup. When the lock is enabled, a three digit passcode is entered. Without the passcode, the user
will be unable to change any settings. The Reset selection does not reset the lock. |
7600-08
28 Feb 1997 |
Paper Source Selection |
| The 7600 series use paper tray selection commands compatable with the HP LaserJet 4.
but with slightly different parameters. |
| 7612, 7617, mL17, mL17e |
7600-05
29 Feb 1996 |
Manual Tray Selection |
| On many page printers, a single sheet inserted into the manual slot will have precedence
over any other tray selection. The mL17 and 7612 have a built in MultiPurpose (MP)/ manual feed tray. By default,
this tray is in the MP mode, and is considered to be a second paper tray selection, and not a manual feed selection. |
7600-06
20 May 1995 |
7612 - Print Quality Issues |
| Print quality problems such as horizontal streaks or ghosting. The printer has been
thoroughly cleaned. The problem may occur immediately after replacing the print cartridge, or there may be a time
interval. |
7600-07
28 May 1996 |
Security Lock Override |
| The 7600 series have a Lock feature to provide security against inadvertent change
to the printer setup. When the lock is enabled, a three digit passcode is entered. Without the passcode, the user
will be unable to change any settings. The Reset selection does not reset the lock. |
7600-08
28 Feb 1997 |
Paper Source Selection |
| The 7600 series use paper tray selection commands compatable with the HP LaserJet 4.
but with slightly different parameters. |
7600-09
28 Feb 1997 |
Paper in MP Tray Prints 2.5" or Blank |
| When printing from the MP tray, only the top 2.5 inches is printed. If the printing
starts more than 2.5" from the leading edge, a blank page is ejected (typically seen with addresses on envelopes). |
7600-10
5 Aug 1997 |
Display Shows T1 LOAD PAPER LETTER, Paper Pulls From Wrong Tray, or Jobs Are Clipped |
| The desired tray is loaded with letter size paper. When printing any of the following
symptoms are displayed: The display Shows T1 LOAD PAPER LETTER (or T2 for Tray 2), Paper pulls from the wrong tray, Jobs are clipped or over-run the page. |
7600-11
13 Jan 1998 |
Jams with New Duplex |
| A new duplex unit jams. |
7600-12
13 Apr 1998 |
Memory Upgrades |
| The 7612 and mL17 use standard 72 pin memory SIMM's, but not all memory may be compatible.
After installing memory, test it with the printer's built in memory check. |
7600-13
1 Oct 1998 |
Windows- Not Printing All Characters |
| When printing from a Windows system, characters in the print job may consistently be
missing, or extraneous characters may print. |
7600-14
12 Jan 2001 |
55 HIGH VOL MALF |
| The printer display shows 55 HIGH VOL MALF. |
|
